What Tire Installation Includes: Mounting, Balancing, Valve Stems, TPMS and Torque

6 min readUpdated November 17, 2026Reviewed by Faisal Mohammad, Licensed Automotive Service Technician

Mounting: getting the tire on the rim without damage

Each wheel comes off the vehicle and goes on a tire changer. The installer breaks the bead, the edge of the tire that seals against the rim, removes the old tire and cleans the rim's bead seat so the new tire seals properly. Corrosion or old rubber left on that surface can cause a slow leak.

The new tire is lubricated, mounted and inflated until the bead seats. A careful installer also checks orientation. Directional tires must roll in the direction of the arrow on the sidewall, and asymmetric tires have a marked outside face. On wheels with direct TPMS, the sensor sits at the valve stem, so the bead has to be worked around it with care.

If the tires are going on a second set of wheels, a good installer also confirms the wheels suit the vehicle before anything is bolted on: the bolt pattern, the centre bore and lug nuts or bolts whose seat type matches the wheel. Wheels bought as part of a package should already be matched, but the check takes seconds.

Balancing: why every new tire needs it

No tire and wheel is perfectly uniform. Balancing spins the assembly on a machine that finds the heavy spots, and the installer adds small weights to even them out. NHTSA says new tires should always be balanced when installed, because an unbalanced wheel can make the vehicle shake or vibrate.

Shops typically use clip-on weights on steel wheels and adhesive weights on the inside of many alloy wheels, where they stay out of sight. If you feel a vibration through the steering wheel at highway speed after a fresh install, a balance re-check and a look for a lost weight are the first things to ask about.

Valve stems and TPMS service parts

The valve stem is a small part that holds all of the air in your tire. Rubber snap-in stems age with heat and weather, which is why many installers replace them whenever new tires go on.

Vehicles with direct TPMS use a sensor attached to the valve stem inside the wheel. One vehicle manufacturer's TPMS service bulletin, published through NHTSA, says the valve core, rubber grommet and washer should be replaced whenever the sensor is removed from the wheel, and that aluminum valve stems need a nickel-plated core rather than brass to prevent corrosion. It is a small step that helps prevent slow leaks at the valve.

TPMS checks after the swap

NHTSA describes two kinds of tire pressure monitoring. Direct systems use a sensor in each wheel. Indirect systems use wheel speed and other vehicle sensors instead. Either way, a careful installer confirms the system is working before you leave.

On direct systems, that can mean reading each sensor with a TPMS tool and, when needed, running a relearn so the vehicle knows which sensor sits in which corner. The same manufacturer bulletin says a relearn is needed when tires are rotated or a new sensor is installed, but not when simply topping up air clears the warning. Procedures vary by vehicle, so ask what yours needs. The TPMS guide explains the warning lights in detail.

Want installation handled for you?

Choose your tires and add installation at an approved independent partner shop at checkout. Have questions about your vehicle first? Request a quote and get an answer by email.

Torque: the step you should never skip

Wheel nuts should be tightened in a star pattern to the vehicle maker's torque specification, usually listed in the owner's manual, using a torque wrench or a torque-limiting tool. Under-tightened nuts can work loose. Over-tightened nuts can stretch studs and be hard to remove at the next tire change.

Some installers suggest a quick torque re-check after the first short drive, especially on alloy wheels, so ask whether yours recommends one. Transport Canada also suggests that each time you check your tire pressure, you take a moment to make sure the tire is securely fastened to the vehicle.

What to ask before and after: a checklist

Pressure deserves its own question. Transport Canada notes that antilock brakes, traction control and stability control may not work correctly if tires are not properly inflated. NHTSA adds that the correct pressure is the one on the vehicle's label, not the maximum printed on the tire.

Scenario: a North York driver picks up a vibration at highway speed a week after a winter changeover. The cause is often simple, such as a lost wheel weight. Raising it early with the installer keeps a small issue small.

  • Is balancing included in this installation?
  • Will the valve stems be replaced, or the TPMS sensors serviced with new seals and cores?
  • Will the TPMS be checked, and does my vehicle need a relearn?
  • What torque spec will be used, and do you recommend a re-check?
  • What pressure will the tires be set to, and does it match my door label?
  • If my vehicle needs an alignment, can it be done at this shop?

Key takeaways

  • A complete installation includes mounting, balancing, a valve stem or TPMS service, correct pressures and proper torque.
  • NHTSA says new tires should always be balanced when installed.
  • When a TPMS sensor comes out of the wheel, its core, grommet and washer should be replaced, per a manufacturer bulletin published through NHTSA.
  • Wheel nuts belong at the maker's torque spec, tightened in a star pattern, with a re-check if your installer recommends one.
  • Alignment is separate: the Brampton, Mississauga, Burlington and Kingston partner shops have a rack; North York and Pickering do not.

Frequently asked questions

Is wheel alignment part of tire installation?

No. Alignment is a separate service that needs an alignment rack. The partner shops in Brampton, Mississauga, Burlington and Kingston have one; the partner shops in North York and Pickering do not.

Do I need new valve stems with new tires?

Rubber snap-in stems age, so many installers replace them with every new set. On direct TPMS sensors, a manufacturer bulletin says the core, grommet and washer should be replaced whenever the sensor is removed from the wheel.

Why is my steering wheel shaking after new tires?

A balance issue or a lost wheel weight is a common cause. Go back to the installer promptly. If you ever suspect a wheel is loose, stop driving and have it checked before going further.

What should I bring on install day?

Your wheel lock key if you have locking lug nuts, and a note of any warning lights already on. If you have a second set of wheels for winter, bring those too.

How do I know what my install fee covers?

The install fee is shown at checkout before you pay. For specifics about your vehicle, such as TPMS relearns, ask through the quote or contact form. Replies come by email.

Sources

FM

Technical review

Faisal Mohammad, Licensed Automotive Service Technician

Faisal Mohammad is a Licensed Automotive Service Technician and operations partner at Tire Installation Near Me. He has 22 years of experience in the automotive industry, with extensive experience in tires, wheels, automotive repairs and partner-installer operations across Ontario.