TPMS Sensors and New Tires: Why the Light Comes On and What to Do

6 min readUpdated November 17, 2026Reviewed by Faisal Mohammad, Licensed Automotive Service Technician

How TPMS works: direct and indirect

NHTSA describes two types of tire pressure monitoring. Direct systems use a sensor inside each wheel. Indirect systems use wheel speed and other vehicle sensors to infer that a tire is low. Both send their information to an on-board processor that lights the TPMS symbol on the dash when pressure falls below an acceptable level.

On direct systems, each battery-powered sensor is usually attached to the valve stem and transmits by radio. A vehicle manufacturer's TPMS bulletin published through NHTSA explains that every sensor has its own ID code, and the vehicle stores which ID belongs to which corner.

In the United States, NHTSA says all passenger cars, light trucks and vans from model year 2008 onward must have TPMS. Many vehicles sold in Canada have it too. Your owner's manual will confirm which type you have.

Reading the warning light

The symbol is either a tire cross-section with an exclamation mark or a top view of a car showing all four tires. How it behaves tells you what is going on.

  • Solid light: at least one tire is significantly underinflated. Check all four with a gauge as soon as possible. NHTSA says the light goes out once the tires are properly inflated.
  • On during a cold morning, off later: likely marginally low pressure that dipped overnight and recovered as the tires warmed. Check and adjust anyway.
  • Flashes for 60–90 seconds, then stays on: NHTSA says this signals a system malfunction, such as a sensor that is not reporting. Adding air will not clear it.

Why the light comes on after a tire swap

A TPMS light right after new tires is common, and it is often not a faulty sensor. These are the usual causes, roughly from most to least simple to fix.

  • Temperature: Transport Canada says tires lose about 1 psi for every 5°C drop. Tires set to label pressure in a warm bay can read low on the first cold morning.
  • No relearn: on many direct systems, a relearn is needed after a rotation or a new sensor so the vehicle knows each sensor's ID and position.
  • No sensors in the new wheels: a second set of wheels without sensors triggers the malfunction warning on vehicles with direct TPMS.
  • A slow leak at the bead or valve, which a few days of pressure checks will reveal.
  • A damaged sensor, or one nearing the end of its battery life.
  • Incompatible wheels: the manufacturer bulletin notes that some aftermarket wheels place the valve hole in a way that stops the sensor working correctly.

How long TPMS sensors last

Direct sensors run on a built-in battery. The manufacturer bulletin states its sensors are designed to last 10 years or 240,000 km. Treat that as one maker's design target, not a guarantee for every vehicle or sensor brand.

The practical point: a sensor can only be replaced with the tire off the wheel. If your sensors are approaching their expected life and the tires are coming off anyway, ask the installer to check them during the same visit. The bulletin also warns that commercially available tire sealants can clog a sensor's pressure port, so mention it if a sealant has ever been used in that tire.

Planning a winter set?

Build a tire and wheel package and add installation at an approved independent partner shop at checkout. Not sure about sensors for your vehicle? Ask in a quote request and get a reply by email.

What a relearn is, and when you need one

A relearn, also called sensor learning or matching, is the process of putting each sensor's ID and position into the vehicle's receiver. According to the manufacturer bulletin, it is needed when tires are rotated, because positions change, or when a new sensor is installed, because a new ID has been introduced. It is not needed when simply correcting tire pressure clears the warning.

Methods differ between vehicles. Some use a TPMS tool or scan tool at the wheel, others use a procedure listed in the owner's manual. Rather than guessing, ask your installer what your vehicle requires.

Winter wheels and TPMS: choosing your setup

If you are buying a winter tire and wheel package for a vehicle with direct TPMS, decide on sensors before you order.

Scenario: a Brampton driver puts winter tires on new wheels without sensors. The light flashes, then stays on at every start. The tires are fine, but the system cannot see them, so the light can no longer warn about a genuinely low tire. The realistic options are adding sensors to the winter set or relying on monthly gauge checks all season.

  • Sensors in both sets: the warning system works year-round. Some vehicles need a relearn at each seasonal swap.
  • No sensors in the winter set: expect a TPMS warning all season on direct systems, and make monthly gauge checks a firm habit.
  • Moving sensors between sets: possible, but it means dismounting both sets every season, which removes most of the benefit of a second set.

A cold-morning pressure check

TPMS is a warning, not a gauge. NHTSA says underinflated tires are hard to spot by eye and that TPMS is not a substitute for regular maintenance, so a monthly check is still the best habit.

  • Check when tires are cold: parked at least three hours or driven less than 2 km (Transport Canada).
  • Use the pressures on the tire information label, not the maximum on the sidewall (NHTSA).
  • Use a good-quality gauge; Transport Canada notes pocket gauges from automotive supply stores are generally more accurate than gas station pumps.
  • Check all four tires, plus the spare if it is full size.
  • In winter, clear snow from the valve before adding air and put the cap back on (Transport Canada).
  • If the light flashes and then stays on, have the system checked.

Key takeaways

  • A solid TPMS light means a tire is significantly low; a light that flashes for 60–90 seconds then stays on means a system fault (NHTSA).
  • Tires lose about 1 psi for every 5°C drop, so a light on the first cold morning after a swap is often just pressure (Transport Canada).
  • A relearn is needed after rotations or new sensors on many vehicles, but not after simply adding air.
  • One manufacturer designs its sensors for 10 years or 240,000 km, so check older sensors while the tires are off.
  • Decide on sensors before buying winter wheels for a vehicle with direct TPMS.

Frequently asked questions

Can I ignore the TPMS light if my tires look fine?

No. NHTSA notes that underinflated tires are hard to detect by eye. Check all four with a gauge. If the light flashes and then stays on, the system itself needs attention.

Do new tires come with TPMS sensors?

No. Sensors are part of the wheel assembly, not the tire. If you are buying new wheels, ask about sensors in a quote request before you order.

Why did my light come on the first cold morning after installation?

Most likely temperature. Tires lose about 1 psi for every 5°C drop, according to Transport Canada. Check the pressures cold and set them to your door label.

Will the partner installer relearn my sensors?

Relearn needs vary by vehicle, and some require a TPMS tool. Mention your vehicle and TPMS setup in a quote request so the details can be confirmed by email before install day.

Can I use tire sealant on a tire with a TPMS sensor?

A manufacturer bulletin published through NHTSA warns that commercially available sealants can clog the sensor's pressure port. If sealant has been used, tell your installer.

Sources

FM

Technical review

Faisal Mohammad, Licensed Automotive Service Technician

Faisal Mohammad is a Licensed Automotive Service Technician and operations partner at Tire Installation Near Me. He has 22 years of experience in the automotive industry, with extensive experience in tires, wheels, automotive repairs and partner-installer operations across Ontario.